# Fligth plan for clifs with vertical facade and sections with terrain variations

**URL:** <https://community.pix4d.com/t/fligth-plan-for-clifs-with-vertical-facade-and-sections-with-terrain-variations/20624>\
**Category:** PIX4Dmapper\
**Created:** [November 29, 2021, 1:46pm UTC](https://community.pix4d.com/t/fligth-plan-for-clifs-with-vertical-facade-and-sections-with-terrain-variations/20624 "2021-11-29T13:46:02Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![purchases](https://avatars.discourse-cdn.com/v4/letter/p/f6c823/32.png) [@purchases](https://community.pix4d.com/u/purchases)\
**Post date:** [November 29, 2021, 1:46pm UTC](https://community.pix4d.com/t/fligth-plan-for-clifs-with-vertical-facade-and-sections-with-terrain-variations/20624/1 "2021-11-29T13:46:02Z")

</div>

We are planning to build an orthomap and a 3D model from a Cliff with vertical walls and other areas with the terrain with variations till the top. The issue is that the area is quite wide, and we will need to perform several flights.

We have found in the forum these suggestions:

> **[How to process images taken at different Flight Heights / GSD?](https://support.pix4d.com/hc/en-us/articles/202558979-How-to-process-images-taken-at-different-Flight-Heights-GSD)**
>
> It is usually recommended to process images captured at the same flight height, as they have the same Ground Sampling Distance (GSD). It means that all images will have the same level of details. T...

> **[Image acquisition plan for terrain with height variations](https://support.pix4d.com/hc/en-us/articles/204656209-Image-acquisition-plan-for-terrain-with-height-variations#gsctab=0)**
>
> IN THIS ARTICLE
> Single flight following the terrain elevation variation (recommended)Multiple flights at different constant altitudesSingle flight at a constant altitude regardless of the terrain c...

But we have some questions regarding the final resolution of the models:

- If we fly at different heights, then the built 3D model and orthomap, which is the final resolution ? Reading seems that is a median, but we need to have a realistic result to make precise measurements.
- In the flight plan, we are planning to do a general plane on top, and then to perform closer flights. Is it ok with this strategy to build up the models, later on?
- Another question is the angle difference among images, for example, in the general plane gimbal might be 90-60 degrees respect horizontal, but in the cliff might be at 0 degrees. Is this an issue for Pix4D ?

Thanks!

---

<div class="post-metadata">

**Author:** ![Daniele\_Lecci](https://sea2.discourse-cdn.com/pix4d/user_avatar/community.pix4d.com/daniele_lecci/32/9493_2.png) [@Daniele\_Lecci](https://community.pix4d.com/u/Daniele_Lecci)\
**Post date:** [December 6, 2021, 9:40am UTC](https://community.pix4d.com/t/fligth-plan-for-clifs-with-vertical-facade-and-sections-with-terrain-variations/20624/2 "2021-12-06T09:40:41Z")

</div>

Hi,

Welcome to the Pix4D Community!

Thank you for your questions.

It is essential to select a suitable acquisition type for your project. You can find more information here:

> **[Step 1. Before Starting a Project \> 1. Designing the Image Acquisition...](https://support.pix4d.com/hc/en-us/articles/202557459-Step-1-Before-Starting-a-Project-1-Designing-the-Image-Acquisition-Plan-a-Selecting-the-Image-Acquisition-Plan-Type)**
>
> Index \> Step 1. Before Starting a Project \> 1. Designing the Image Acquisition Plan
> 
>  Previous  |  Next 
> 
> 
> 
>  
> Pix4Dmapper is an image processing software that is based on automatically findin...

You could proceed as follows:

-Acquire your area of interest from above using a grid pattern (eventually double grid)  
-Acquire your cliff from the side using an acquisition plan more adapted for 3D reconstruction

(make sure that you have areas that can be seen from the other project in both projects. Make sure you have overlap between the projects)

-Merge the two projects (as described in the following article)

> **[How to merge projects](https://support.pix4d.com/hc/en-us/articles/202558529-How-to-merge-projects)**
>
> It is possible to merge projects for which step 1. Initial Processing has already been completed in Pix4Dmapper. This allows the combination of information from different projects into one single...

Cheers
